Our slop closets have been developed over the years in close collaboration with our customers. Today, we have three different models available in our product range. Further information about our different models can be found below.

Slop closets are used for flushing sewageable solid and fluid waste into the drains. Kidney dishes, bottles, etc. are emptied into the closet and flushed using a flushing valve.

The closet comes with a plastic stench trap

Slop closet 3070

Suitable for locations where solid and fluid sewageable waste is poured into the drains and flushed with edge flushing into the sewer.

Slop closet 3070 is used in service stations and camping sites for emptying septic tanks, for example.

  • Dimensions: 550x600x900 mm
  • Working height: 800 mm
  • Discharge pipe Ø: 110 mm
  • Accessories: hinged container grate or cover
Slop closet 3070

Slop closet 3071

In addition to edge flushing, slop closet 3071 also features bottle and bottom showers for rinsing the containers emptied into the sink.

Pouring closet 3071 is commonly used in, for example, the servicing rooms of in-patient wards, for emptying the bedpans.

  • Dimensions: 550x600x900 mm
  • Working height: 800 mm
  • Discharge pipe diameter: 110 mm
  • Accessories: hinged container grate or cover
Slop closet 3071

Slop closet 3071V

Slop closet 3071V has been developed from model 3071 to facilitate the pouring of containers emptied into the sink. The sloping-edged slop closet is becoming increasingly popular due to its improved usability and ergonomics.

  • Dimensions: 550x600x1000 mm
  • Working height: 700 mm, slanted front edge
  • Discharge pipe diameter: 110 mm
Slop closet 3071V

Further information

The flushing valve of the slop closet releases a large amount of water into the sink in one go, so to attain proper flushing, a cold water supply must be provided using a DN28 connection, the recommended pressure in the pipe being 4.0–6.9 bar. The slop closet is connected to a DN100 drain line.

The outer dimensions of the slop closet are 550x600x900 mm (models 3070 and 3071) and 550x600x1000 mm (3071V).

Pouring closets are available in three different models. Our sales department will assist you in choosing the right model.

CLEANING
Stainless steel equipment and fixtures must be cleaned on a regular basis to prevent them from rusting. A water wash is often sufficient for cleaning a stainless steel surface; hot water and steam can be used in special cases.

Impurities and deposits that have adhered to the surface can be removed by rubbing them with an emery cloth, for example. NOTE! The emery cloth must be non-ferrous. It is advisable to first try the treatment on a less noticeable part of the product.

DETERGENTS
Standard cleaning powders or power detergents such as soda, borax or sodium perborate can be used for cleaning stainless steel surfaces.

Alkaline solutions, such as soda, ammonia and diluted soda lye, can be used for dissolving grease. Acetone, petrol, alcohol and similar organic solvents can also be used for removing grease deposits or other water-insoluble matter.

Detergents that contain sulphuric or hydrochloric acid may not be used for cleaning stainless steel surfaces.

DISINFECTION
The sterilising agents used for disinfection often contain sodium hypochlorite or potassium hypochlorite. However, these substances are dangerous to stainless steel as they easily give rise to pitting corrosion. Other disinfectants that contain chlorine, such as chloramines, are also dangerous. The most affordable disinfectant that is suitable for stainless steel is nitric acid; even mild concentration solutions have a bactericidal effect.

TREATMENT AFTER CLEANING
The detergent must be carefully cleaned from the steel surface. Rinsing with plenty of water is usually sufficient for this purpose. If acidic detergents are used, a pre-rinse should be carried out with a neutralising solution, such as soda.

The user must always ensure that the room concerned is sufficiently ventilated, proper protective gear is used and any in-house occupational heath and safety instructions are complied with.